English
Ελληνικά
Water softener Classic 75lt Runxin F63 Volumetric 4m³/h
Complete water softening system consisting of Runxin F63 automatic volumetric head with integrated bypass, 75lt Pressure vessel and 100lt brine tank.
Automatic volumetric softenerSent by arrangement throughout Greece
Complete water softening system consisting of:
- Runxin F63 Volumetric automatic volumetric head with built-in bypass
- Pressure vessel 75lt ( diameter 33.5 cm, height 140 cm) Approximate dimensions
- Brine bucket 100lt ( width 40 cm, depth 40 cm and height 90 cm) Approximate dimensions
Electronic Volumetric Head F63
Runxin's F63 volumetric electronic head (valve) has a pulsed flow meter (turbine type) and when the user-defined "cubic degrees" are reached, the process of resin regeneration begins. The time of regeneration is determined by the user. We usually set it late at night so that there are no consumptions.
The regeneration process takes place in 4 cycles, all of which are configurable:
- Backwash : Resin preparation. The resin is rinsed in the maximum flow of water to prepare it for the next step. We usually set it from 3 to 8 minutes depending on the installation.
- Brine & Slow Rinse : In this stage the head draws the salt water (sodium chloride) from the brine tank and irrigates the resin with it. It is the longest stage and lasts at least 60 minutes.
- Brine Refill: The head refills the brine tank with water. This process takes from 3 to 10 minutes depending on the installation.
- Fast Rinse : The resin is rinsed at maximum flow to remove salt residue and return to its original state ready to deliver softened water again. This process takes from 5 to 10 minutes depending on the installation.
Dupont DOW DOWEX HCR-S/S Softening Resin
Dupont Dow Chemicals is the world's largest resin manufacturer. Based in America, it counts over 600 resins specialized for hundreds of applications.
The resin we use DOWEX HCR-S/S is a strong cationic suitable for potable water softening applications. It is WQA certified to NSF/ANSI-61 and complies with the US FDA Regulation 21 CFR 173.25. The resin absorbs the Calcium Ca2+ and Magnesium Mg2+ ions, elements which make up the hardness of the water, the so-called salts. The resin is charged with Na+ ions and has a total capacity of 1.9 eq/L. Each time it becomes saturated it will need regeneration with >99.5% purity sodium chloride (salt).
Technical Characteristics
| Head Type | RUNXIN F63 volumetric with integrated by-pass |
| Water Supply | 4m³/h |
| Operating Pressure | min 2 Bar – max 6 Bar |
| Renaissance type | Down Flow |
| Water supply entrance / exit | 1" male thread |
| Drainage Softener | Φ16 |
| Electrical Connection | 220V/12V – 50Hz |
| Brine Tank | Polypropylene (PP) gray color |
| Pressure vessel | 12" X 48" with DOW DUPONT DOWEX HCR-S/S Strong Cationic Resin |
| Amount of Resin | 75 liters |
| Capacity Cubic Degrees | 276 (m³ x °F) |
| Temperature Range | min 5°C – max 50°C |
| Power supply | 230 VAC / 50 Hz |
Conditions for Correct Operation of the Softener
- If the mains pressure is above 6 bar, a pressure reducer is recommended.
- Installation of a sediment filter before the softener inlet to protect the head.
- It is recommended to use salt in tablets due to its high purity.
Important
- For the right choice of softener and for any other information, please contact us, we will be happy to serve you.
- The softeners before they are shipped can be adjusted by us according to your needs.
- When starting the softener for the first time, our technicians can guide you with the necessary information.
